Welcome to the Raisonance Support Website

Topic : RLink Adaptors: What is a "JTAG-SWD"

Forum : ARM

Original Post

Post Information	Post
June 23, 2008 - 10:59am Guest	The FAQ says there are 3 different adaptors: http://www.raisonance.com/Forum/punbb/viewtopic.php?id=2449 . This now seems to be out of date and longer seems to be true! I've just received an RLink kit, and it came with 3 adaptors: JTAG-uPSD ADP ICC-ST7 and SWIM-STM8 JTAG-SWD There is no JTAG-ARM. The documentation still refers to JTAG-ARM, and makes no mention of the JTAG-SWD; in fact, I can't find any reference to it anywhere on the Raisonance site. I'm guessing that the JTAG-SWD must replace the JTAG-ARM for use with STM32 - but it has two jumpers, and no indication of how they need to be set for use with an STM32.

Replies

Post Information	Post
+1 0 -1 June 23, 2008 - 11:28am Raisonance Support Team	Hi, The JTAG-SWD indeed replaces the JTAG-ARM but will also allow SWD in the future. For now, you should place both jumpers in the "JTAG" position, as the software does not handle SWD yet. In fact they should already be set correctly from when you received them, if you haven't unplugged them. So you don't need to change anything. Later, you will have the choice to use either JTAG or SWD, as STM32 allows to connect using both protocols. Best Regards, Vincent
+1 0 -1 June 23, 2008 - 10:42pm Guest	Hmm... someone slipped-up by shipping these things before the documentation was ready, eh?! Surely it could at least have been mentioned on the website?! :rolleyes: Anyhow, yes; the jumpers did happen to be in the correct position - but how could I know that without any documentation to confirm it?! For the record, here is the JTAG-SWD adaptor with the jumpers set for JTAG mode: See also: http://www.raisonance.com/Forum/punbb/viewtopic.php?id=2520
+1 0 -1 June 25, 2008 - 6:05pm Raisonance Support Team	Hi, I will update the doc about that for the next release of RIDE. If you don't mind, I'll use your picture. That will save me 10 minutes looking for the camera. ;) Is it OK for you? Best Regards, Vincent
+1 0 -1 June 26, 2008 - 12:53pm Guest	That's fine - I can let you have a higher-resolution one, if you like?
+1 0 -1 June 26, 2008 - 3:08pm Raisonance Support Team	Hi, Thanks for the picture. (and for telling us that this point was missing in the doc) I don't need a higher-resolution version; In fact I even had to reduce the resolution of the one you posted for the pdf file not to be too large. Best Regards, Vincent
+1 0 -1 June 26, 2008 - 3:34pm Guest	VincentC wrote: I even had to reduce the resolution of the one you posted for the pdf file not to be too large. Oh yes, I remember - I didn't adjust the resolution for posting; I just increased the JPEG compression...! :cool:
+1 0 -1 February 28, 2017 - 5:41pm Andru Rom	Hello.Please give an answer. The RXLink software is already support SWD interface?
+1 0 -1 March 6, 2017 - 9:52am vincent choplin	Yes
+1 0 -1 October 22, 2017 - 1:53am Mormilo Sergey	Hello.Please give an answer. And how do I connect STM32 through JTAG adapter? Where to get these pinouts? Why not make a photo showing the pins and signals?